Wednesday, September 20, 2017 Register
 
www.cyberspacesolutionsinc.com

 

Follow Us On: FacebookTwitterYouTube

www.cyberspacesolutionsinc.com Bookmark and Share
Search
 
Suspension Minimize
How Does it Work Series - Suspension

How do forks work?

The simple explanation is that they absorb bumps. The not-so-simple explanation follows.

Forks, or any suspension, for that matter absorb bumps by allowing the force of the impact to compress a spring. However a spring by itself will release that energy by expanding with the same amount of force. To avoid getting launched into orbit, damping is employed. This controls the rate at which the spring energy is released. This was such a good idea that compression damping is used to regulate how much energy is absorbed by the spring. Damping is accomplished by fork oil and the shim stacks.

Compression Damping

When the fork hits an object, the energy of the impact is absorbed by the springs. Compression damping regulates how fast this energy is absorbed. This preserves control and prevents bottoming. The key is the oil. In the bottom of the forks there is a reservoir of oil. After impact the fork compresses and shrinks the size of the reservoir. The oil is then forced into the top of the forks. The speed of the oil transfer is regulated by the size of the ports and by the shim stacks. A shim stack is a thin metal washer that covers the port. It takes a certain oil pressure to bend the shim so that oil can pass. When the reservoir is compressed the oil pressure is increased. More compression is equal to more pressure.


Preload Adjustment - Rear Shock, Top


Compression Adjustment - Front Forks, Top.

Rebound Damping

A undamped spring when compressed will release it's energy instantaneously. The result is comedic unless it's attached to the front end of your bike. The rebound damping allows the release to be controlled. The mechanism is similar to compression damping, except for the fact that now the oil is sucked back into the bottom reservoir as it expands after impact.


Rebound Adjustment - Rear Shock, Bottom


Rebound Adjustment - Front Forks, Bottom

Suspension maintenance tips

The quick linkage lube job

Few of us like doing this, but it is a necessary evil.

The tools:

You will need your basic tool kit, a stand and a 10 inch block

1.) Remove the link bolt that fastens the linkage to the swingarm. This allows greater access to the shock bolt and other link pivot bolts. Watch out for thin shim washers used between the plates.

2.) Remove the seals and the bushing from the linkage. Use a degreaser and a shop towel to remove the old grease. If the seals are dry then replace them.  If the bushings and bearings are corroded then replace them as well.  Use a large C-clamp to push the old bearings out.  Be careful with the needle bearings since the only thing that keeps them in is the stiction of the grease.

3.) To get access to the swingarm pivot bearings, pull the chain off the rear sprocket and swing the arm and wheel back.. Remove the seals and bushings and regrease. When you retighten the swingarm bolt then tighten it to the proper torque. Overtighten and affect the suspension damping.  Undertighten and the linkage will twist causing premature wear.

4.) Regrease all the bolts before you install them so that they don't seize.  Then after installing them, wipe the threads off and apply blue loc-tite to secure the bolts.  Wipe excess grease off the outside of the linkage because it will be a magnet for dirt.

Preventing fork bind

You can screw up a perfectly good pair of forks simply by misadjusting them. This will mimic the effects of damaged forks.  Since we don't need that then here's some tips to avoid that

1.) Tighten the triple clamp bolts up to the listed torque values given in the manual. Tighten them too tight and the forks will bind as they pass the clamps.

2.) When you replace the front wheel, keep one side of the axle bolts a little loose.  Then push the front end down and then tighten down the bolts to torque.  This will make sure the forks are aligned.

3.) Put the right spacers in the right spot.  If you are missing spacer then don't tighten the axle nut because the forks will pull together.

  
 
 

 

 

WARNING! DO NOT USE ANY OF THE INFORMATION CONTAINED ON THIS SITE UNLESS YOU READ AND AGREE TO THE FOLLOWING INFORMATION.

 


Involvement in off-road motorcycling and related activities carries a significant risk of damage to property, personal injury or death. Participate at your own risk!
The publishers of
www.dirtridersofcolorado.com recommend the use of professional instruction before entering into any sports or physical activity. You should become knowledgeable about the risks involved and assume personal responsibility for your actions.
The information contained within
www.dirtridersofcolorado.com may or may not be accurate and is open to interpretation. Opinions concerning the technical difficulties, fitness requirements, safety, and ratings, are subjective and may differ from yours or others opinion, therefore be warned that you must exercise your own judgment as to the difficulty and your ability to safely protect yourself from the inherent risks and dangers. Do not use the information provided on this site unless you are a skilled and experienced sports person who understands and accepts the risks of participating in dangerous sports and activities.
Whilst
www.dirtridersofcolorado.com makes reasonable efforts to include accurate and up to date information on this website, errors or omissions sometimes occur, therefore the information contained on www.dirtridersofcolorado.com is provided "as is" and without warranties of any kind either expressed or implied. Viewing, reading, or any other use of the information contained within this web site is purely the voluntary will of the viewer or user. You, 'the viewer' or 'user' shall not hold the publisher, owner, authors or other contributors of www.dirtridersofcolorado.com responsible for any incidents related directly or indirectly to the materials published within this site or its network of web links. www.dirtridersofcolorado.com assumes no liability or responsibility for your actions.

Please see our complete terms of use by clicking the "Terms Of Use" link at the bottom of this page.
 

 

www.cyberspacesolutionsinc.com
 
 
www.cyberspacesolutionsinc.com www.cyberspacesolutionsinc.com www.cyberspacesolutionsinc.com